Poxi-Rock Primer
- 1.5 Gallon BAG-PAKTM Unit in a single pail
- 3 Gallon BAG-PAKTM Unit in a single pail
- 15 Gallon Unit in three 5 gallon pails
- 165 Gallon Bulk Unit in three 55 gallon drums
- 100% solids
- Versatile Product
- Excellent adhesion
- Vertical/Horizontal application
- Odorless / VOC Compliant
- Easy mix ratio
- Can be field pigmented
Description
POXI-ROCK PRIMER is a 2-component, clear (slightly amber), 100% solids epoxy primer formulated to provide excellent adhesion to concrete over dry surfaces. This workhorse epoxy primer is intended for application at temperatures between 60°F and 85°F. POXI-ROCK PRIMER meets all USDA/FDA guidelines for use in federally inspected facilities.
Uses
POXI-ROCK PRIMER is an excellent multi-purpose primer suitable for vertical and horizontal application. It deeply penetrates the substrate and provides an ideal surface for subsequent coats. With the addition of fillers, such as a fumed silica or sand, POXI-ROCK PRIMER also makes an ideal patching material for floors, walls and ceilings.
Typical Coverage
POXI-ROCK PRIMER is typically applied between 100-160 square feet per gallon per coat depending upon substrate and project requirements
Physical Properties
Volume mix ratio | 2 to 1 (Resin to Hardener) |
Viscosity (mixed) | 600-950 CPS Typical |
Solids Content (%) | 100 % (ASTM D-2697) |
VOC | Compliant with all US Regulations |
Application Temps. | 60° – 85° F |
Hardness (ASTM D-2240) | 65-75 (Shore D) |
Gel Time | 20-30 minutes @ 75° F |
Dry to Touch (recoat with compatible product) | 2-5 hours @ 75° F |
Through Cure | 4-6.5 hours @ 75° F |
Open to light traffic | 24+ hours @ 75° F |
Shelf Life | 1 Year in unopened units |
Limitations & For Best Results
- Do not thin this product.
- Do not apply when Humidity exceeds 70% indoors
- Do not allow to puddle during application
- Allow each coat to dry to 'tack-free' or clear prior to re-coat.
- When re-coating, always apply the next coat within 24 hours of completing the previous coat.
- Do not apply this product heavier / thicker than the recommended spread rate / mil thickness
Product Application
Apply using brush, roller and squeegee. ROCK-TRED product test data is based on environmental temperatures of 75° F. Viscosity and working time are always affected by temperatures above or below that mark. When applying product always consider the ambient, surface, and product temperature at the time and place of installation.
Color and Textures
POXI-ROCK PRIMER is manufactured in CLEAR (slightly amber), can be field pigmented using ROCK-TRED Colorants. Most ROCK-TRED products are available in a wide range of textures using an appropriate aggregate.
Chemical Resistance
Always refer to ROCK-TRED's chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.
Product Storage
DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.
Surface Preparation
Always apply ROCKTRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Mechanical preparation by means of a shotblasting or diamond grinding machine to a minimum CSP-2 profile is the best and recommended preparation method for POXI-ROCK PRIMER applications. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.
Clean Up
Application tools and equipment can be cleaned with soap and water immediately after use, or with solvent once the product has begun to cure.
Disposal
Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.
Important Notice
Always read and acquaint yourself with ROCK-TRED's Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty.